How to Replace a Kitchen Faucet

To give your kitchen a full renovation, replacing the kitchen faucet is one of the most important things to do.  If your kitchen is outdated or leaking water, you must think to give it a change to update it. replacing the kitchen faucet is not so hard task that you cannot do it yourself. Follow the instructions to get a good result.

How to Replace a Kitchen Faucet?

A kitchen faucet is fitted with mechanism to control the water flow. It has an on-off button by which you can control the water flow. To install a new faucet is simple if you know the whole process but you might face problems to remove the old one. The problems include rusty pipes, rough position of the nuts and many more but it is easy to tackle the problem if you follow the instructions properly.

Changing the Faucet

The whole process of changing the faucet is divided into two parts:

  1. Removing the old kitchen faucet
  2. Install the new faucet

Necessary Tools

You cannot change the faucet without some tools. Removing the old faucet requires more tools than installing the new one. The important tools for doing this job successfully you will need:

  1. Work light
  2. Flashlight
  3. Wrench set
  4. Screwdriver
  5. Hand saw
  6. Hammer
  7. Pliers
  8. Pipe wrench
  9. Bowls
  10. Rags
  11. Safety goggles
  12. Tube cutter

All of these tools may not be needed but it is good to have every tools for any bad circumstances when working.

Preparation for Replacement

Firstly, you need to gather all the necessary tools and if you don’t have any, buy them and make them ready for doing the work. You need to check out the faucet type, the number of holes and other equipment. Measurement between the holes is important because your new faucet type depends highly on it while fixing. You could take the picture of your faucet type and this will help finding the same type of faucet.

Moreover, there are about four types of kitchen faucet such as compression, ball, cartridge and disc. Ball and disc are single handled and compression faucets are double handled while cartridge faucets are either double handled or single. Better quality faucets are expensive but it lasts long.

Removing the Old Faucet

The most challenging part of this whole work is to remove the old faucet. Successful replacement of the new faucet depends on how accurately you remove the old faucet. The steps are given below.

Step 1

You have to lay under your sink and take a position in which you are comfortable enough to do all things and you should wear your safety goggles for your eye’s safety. Look under the sink with a flashlight and keep the necessary tools by your side and set a work light to work and focus.

Step 2

Separate the lines of drains and P-traps and make the faucet free to access. Take a bowl to excess the drain water. you will need a cloth to clean the ground and work perimeter. You may also need the pipe wrench or tube cutter to complete these steps. Wrenches could help to detach the supply line and tube cutters are used to cut the copper lines.

Step 3

If you have a garbage disposer, you should disconnect it but ensure that you have turn off the power. At first unscrew the disposer from the sink and then detach it by using a screwdriver that you will find under the ring.

Step 4

The foremost water supply should be cut off through the valves and release the pressure by opening the faucet. Turn the faucet on to ensure that the supply has been seized. If the result is negative, it could cause injuries.

Step 5

Behind the basin, there are tailpiece nuts where you have to fit the wrench jaws to loosen the joint. After opening the faucet, detach the nozzles to get the faucet out. Sometimes, the nuts are rusty and you need to put oil over it to make this task easier.

Fixing the New Faucet

The easiest way to fix a new faucet is to apply the instructions in the manufacturer otherwise, you could also follow the steps:

Step 1

The flange is used for connecting pipes, valves, joints and other accessories. Settle down the flange over your new faucet opening.

Step 2

You should check how the handle and the faucet work prior to mounting it and this will make you sure that you don’t tight the wrong one. Hand tighten the nuts of the flange.

Step 3

Fit the nozzles in the faucet and tighten the joint of the tube. Without any disturb, the hose pipe works only if you let the spray nozzle spread out of your faucet.

Step 4

The supply that have been detached before, reassemble them again. Put everything in correct place and follow the lines that you have done when removing the old one.

At last, confirm that you have done everything accurately and make it sure that there is no leakage. If you find any leakage, tighten the connections again. Here is all you need to know about how to replace your kitchen faucet.

Previous articleHow to Make Energy Bars for Cycling: Complete Instruction
My name is Michael N. Hackney and I am a registered Pharmacist. I received my bachelor of science in biology from the University of Kentucky and my doctor of pharmacy from Campbell University. I had completed a community pharmacy residency at the UNC Eshelman School of Pharmacy and Moose Professional Pharmacy in Concord. After working as a pharmacist for almost twenty years, I took a detour on my career path to pursue a role as a blogger, a fitness blogger in exact focusing on the supplements. In my writing, I try to tell my readers about different exercise supplements, their good and bad sides, medical recommendations, risks, dosage, and experts' recommendations. There will be plenty of information shared on losing weight, building muscle, eating healthy, and living a happy, healthy life on my blog. I enjoy blogging and strive to share accurate information about nutrition and health knowledge. My blog is for those who are on the journey of acquiring a healthy life through proper fitness guide. I am happily married and have two children. I live in Queens, NY with my wife.

LEAVE A REPLY

Please enter your name here
Please enter your comment!